How to receive - Revision history

Clanker: Link the Receiving guide

2026-10-24T20:06:19Z

Link the Receiving guide

← Older revision		Revision as of 20:06, 24 October 2026
Line 6:		Line 6:
	# In SDR++, choose the RTL-TCP source and enter that address and port.		# In SDR++, choose the RTL-TCP source and enter that address and port.

	~~[[Getting Started#6. Receive\|Getting Started]] and~~ [[SimTX Guide/~~Stations#Receive at a station\|Stations~~]] ~~explain the~~ receive ~~settings~~.		[[SimTX Guide/Receiving]] describes every receive setting.

	== Receiving with RTL-TCP ==		== Receiving with RTL-TCP ==

Clanker: Add receiving with the SimTX desktop app

2026-10-24T19:41:28Z

Add receiving with the SimTX desktop app

← Older revision		Revision as of 19:41, 24 October 2026
Line 1:		Line 1:
			== With the SimTX desktop app ==
			The app connects your SDR program through a bridge on your own computer:
			# In the '''Receive''' tab, choose '''Where you listen''': one of your stations, a public station, or '''Ad-hoc'''.
			# Under '''Tuning''', set the '''Center frequency''' and the '''Sample rate (Hz)'''.
			# Press '''Start RX'''. The '''Bridge''' section shows the address to use, by default <code>127.0.0.1</code> and '''rtl_tcp port''' <code>1234</code>.
			# In SDR++, choose the RTL-TCP source and enter that address and port.

			[[Getting Started#6. Receive\|Getting Started]] and [[SimTX Guide/Stations#Receive at a station\|Stations]] explain the receive settings.

			== Receiving with RTL-TCP ==
	It is very to receive your and other people signal with RTL-TCP.		It is very to receive your and other people signal with RTL-TCP.

Bmcgeneral at 14:45, 14 September 2026

2026-09-14T14:45:21Z

← Older revision		Revision as of 14:45, 14 September 2026
Line 26:		Line 26:

	* '''Try "argon.simtx.net:1240"'''		* '''Try "argon.simtx.net:1240"'''

			[[Category:SimTX]]

Bmcgeneral: Created page with "It is very to receive your and other people signal with RTL-TCP. Most of SDR applications support RTL-TCP, Took SDR++ as example: How to receive == Q&A == === Q: What sample rate should I use? === * '''250KHz (0.25MSPS) for receiving Shortwave and lower band''' * '''1.024MSPS (or higher) for receiving FM, wide signal''' === Q: I don't see anything? === * '''Make sure you type in the right information''' * '''Ma..."

2026-09-14T14:45:11Z

Created page with "It is very to receive your and other people signal with RTL-TCP. Most of SDR applications support RTL-TCP, Took SDR++ as example: center|frameless|732x732px|How to receive == Q&A == === Q: What sample rate should I use? === * '''250KHz (0.25MSPS) for receiving Shortwave and lower band''' * '''1.024MSPS (or higher) for receiving FM, wide signal''' === Q: I don't see anything? === * '''Make sure you type in the right information''' * '''Ma..."

New page

It is very to receive your and other people signal with RTL-TCP.

Most of SDR applications support RTL-TCP, Took SDR++ as example:
[[File:Receive guide.png|center|frameless|732x732px|How to receive]]

== Q&A ==

=== Q: What sample rate should I use? ===

* '''250KHz (0.25MSPS) for receiving Shortwave and lower band'''

* '''1.024MSPS (or higher) for receiving FM, wide signal'''

=== Q: I don't see anything? ===

* '''Make sure you type in the right information'''
* '''Make sure you are tuned in the right frequency'''
* '''Try using manual gain or RTL-TCP if you are on higher band'''

=== Q: What band should I receive? ===

* '''Try 60m SW band (4700 - 5100KHz)'''
* '''or FM band (87.5 - 108MHz and recommend using RTL-AGC / Manual gain)'''

=== Q: I don't see the port box. ===

* '''Try "argon.simtx.net:1240"'''